What Is DI Water? Deionized vs Distilled vs Ultrapure
DI water (deionized water) is water that has had almost all of its dissolved ions removed, such as sodium, calcium, magnesium, chloride, sulfate and bicarbonate. It is made by passing water through ion exchange resins, and labs use it to prepare solutions, rinse glassware and feed instruments where minerals would interfere with results.
This guide explains how deionization works, how DI water compares with distilled and ultrapure water, which water grade your method needs, and what a DI water filter can and cannot do.
What is DI water?
Tap water carries dissolved salts. In solution these salts split into charged particles: cations (positive, for example Na+, Ca2+, Mg2+, Fe2+) and anions (negative, for example Cl-, SO42-, HCO3-, NO3-). Deionization removes these charged particles.
What deionization does not remove well:
- uncharged organic molecules
- particles
- bacteria, viruses and endotoxins
- dissolved gases that do not ionise strongly
That is why DI water is a measure of ionic purity, not total purity. A laboratory water system combines deionization with other steps when the method needs low organics or bacteria.
How is deionized water made?
Deionization uses ion exchange resins: small polymer beads with charged sites on their surface.
- Cation resin holds hydrogen ions (H+). When water passes through, it captures cations such as Ca2+ and Na+ and releases H+ in their place.
- Anion resin holds hydroxide ions (OH-). It captures anions such as Cl- and SO42- and releases OH-.
- The released H+ and OH- combine to form water (H2O).
The resins can sit in two separate columns (two-bed) or be mixed in one column (mixed bed). Mixed bed gives higher purity because each drop of water meets cation and anion sites many times.
Resin has a fixed capacity. Once its sites are used up, ions start to pass through and the water quality drops. The resin is then replaced or regenerated with acid and caustic solutions.
How to deionize water in a lab
In practice, labs rarely run tap water straight through resin. A typical sequence is:
- Pre-filtration and activated carbon, to remove particles and chlorine (chlorine damages resin and membranes).
- Reverse osmosis (RO), which removes most ions, organics, particles and bacteria and takes most of the load off the resin.
- Ion exchange or electrodeionization (EDI), which removes the remaining ions. EDI uses an electric current to keep the resin regenerated continuously, without chemicals.
- Polishing for ultrapure water: a final mixed-bed cartridge, UV lamp to break down organics and kill bacteria, and a 0.2 µm filter or ultrafilter at the outlet.
Feeding resin with RO water rather than tap water means the cartridges last much longer and the output quality is more stable.
Deionized vs distilled vs ultrapure water
These terms describe how the water was made, not a fixed specification. The table shows the practical differences.
| Distilled water | Deionized (DI) water | Ultrapure water (Type I) | |
|---|---|---|---|
| How it is made | Boiling water and condensing the steam | Ion exchange resin (often after RO) | RO + ion exchange or EDI + UV + final filtration |
| Removes ions | Most | Almost all | Almost all, to 18.2 MΩ·cm |
| Removes organics | Partly (volatile organics can carry over) | No (resin can even release some) | Yes, to low TOC levels |
| Removes bacteria and particles | Yes, at the point of production | No, unless filtered | Yes (0.2 µm filter or ultrafilter) |
| Energy and running cost | High energy use for boiling | Low energy, resin replacement | Higher, consumables and maintenance |
| Typical use | General rinsing, autoclaves, some media | Buffers, reagents, rinsing, feed water for instruments | HPLC, ICP-MS, PCR, cell culture, trace analysis |
"Milli-Q water" is a trade name for ultrapure water from one manufacturer's systems. In lab conversation it is used as a synonym for Type I water. Compared with distilled water, it has far fewer ions and organics, and it is produced on demand rather than stored.
Lab water grades: ASTM D1193 and ISO 3696
Instead of "distilled" or "DI", methods and SOPs should name a water grade. Two standards are used most often.
ASTM D1193 reagent water types
| ASTM D1193 type | Resistivity, min. (MΩ·cm at 25 °C) | Conductivity, max. (µS/cm at 25 °C) |
|---|---|---|
| Type I | 18.0 | 0.056 |
| Type II | 1.0 | 1.0 |
| Type III | 4.0 | 0.25 |
| Type IV | 0.2 | 5.0 |
Note that in ASTM D1193 Type III has a stricter resistivity limit than Type II. The types are not a simple ranking; the standard also sets limits for TOC, sodium, chloride and silica, and lists the production method for each type. Check the current edition when you write a specification.
ISO 3696 grades
| ISO 3696 grade | Conductivity, max. (mS/m at 25 °C) | Same value in µS/cm | Absorbance at 254 nm, max. (1 cm) | Typical use |
|---|---|---|---|---|
| Grade 1 | 0.01 | 0.1 | 0.001 | HPLC, trace analysis, very demanding methods |
| Grade 2 | 0.1 | 1 | 0.01 | Sensitive analytical work, atomic absorption |
| Grade 3 | 0.5 | 5 | not specified | Most wet chemistry, reagent preparation |
Many lab water suppliers also use "Type 1, 2, 3" informally: Type 1 for ultrapure, Type 2 for general lab grade (often RO + EDI), Type 3 for RO water used for rinsing and feeding other systems. When an auditor or a method asks for a grade, use the standard's definition, not the informal one.
Conductivity of DI water
Water quality is checked by measuring how well it conducts electricity. Ions carry current, so fewer ions means lower conductivity and higher resistivity.
- Theoretically pure water at 25 °C has a resistivity of 18.2 MΩ·cm, which equals a conductivity of about 0.055 µS/cm.
- Resistivity (MΩ·cm) and conductivity (µS/cm) are inverse: 1 MΩ·cm = 1 µS/cm, 18.2 MΩ·cm ≈ 0.055 µS/cm.
- Both values depend strongly on temperature, so meters compensate to 25 °C.
DI water does not stay at its outlet quality. Once exposed to air it absorbs carbon dioxide, which forms carbonic acid. Resistivity falls and the pH drifts slightly acidic, to around 5.6. This is why ultrapure water is dispensed fresh and not stored in open bottles, and why measuring the pH of pure water with a normal pH electrode gives unstable readings.
What is a DI water filter?
A DI water filter is a cartridge or canister filled with ion exchange resin, usually mixed bed. Water flows through and leaves deionized. They are used:
- as the final polishing stage after RO in lab water systems
- on their own, to feed small instruments, autoclaves, humidifiers or glassware washers
- outside the lab, for spot-free car and window washing and aquariums
Points to check when choosing or running one:
- Capacity. It depends on resin volume and feed water hardness. Hard tap water exhausts a cartridge much faster than RO water.
- Monitoring. Use an inline conductivity or resistivity meter, or colour-indicating resin that changes colour as it is exhausted. Replace on the reading, not the calendar.
- Bacteria. Resin beds that stand still can grow bacteria. Flush before use and add a 0.2 µm filter after the cartridge if the application is sensitive.
- Chlorine. Protect the resin with activated carbon pre-treatment if you feed tap water.
Why is DI water used in labs?
Ions in tap water interfere with almost every analysis:
- They change the concentration of prepared solutions and buffers.
- They show up as peaks or background in ion chromatography, ICP and AAS.
- Calcium and magnesium leave scale in autoclaves, water baths, humidified chambers and washers.
- Metal ions can inhibit enzymes and affect cell growth.
- Residues on glassware carry over into the next sample.
Using water of a known, documented grade removes one variable from every result.
How BIEL can help
BIEL engineering supplies the laboratory equipment that depends on clean water, from Memmert water baths and humidified chambers to BUCHI Kjeldahl and evaporation systems. We install, calibrate and qualify (IQ/OQ/PQ) the equipment we supply, and build complete turnkey labs with eLaborator lab furniture. See our water baths, filtration supplies, lab instruments and services.
FAQ
Is DI water the same as distilled water?
No. Distilled water is made by boiling and condensing, which removes ions, most non-volatile contaminants and bacteria. DI water is made by ion exchange, which removes ions more completely but leaves organics and bacteria unless other steps are added.
How do you make deionized water?
Pass water through cation and anion exchange resins, usually after carbon filtration and reverse osmosis. The resins swap dissolved ions for H+ and OH-, which combine into water.
Why is deionized water used in labs?
Because dissolved minerals change solution concentrations, interfere with analysis, scale equipment and contaminate glassware. DI water gives a known, low-ion starting point.
Is DI water safe to drink?
Drinking a small amount is not dangerous. It is not recommended as a regular drinking water, because it contains no minerals and lab DI water is not produced, stored or tested to drinking water standards. Do not drink water from lab dispensers.
What is the conductivity of DI water?
It depends on the grade. Ultrapure Type I water reaches about 0.055 µS/cm (18.2 MΩ·cm) at 25 °C. General lab-grade DI water is typically at or below 1 µS/cm. Exposure to air raises conductivity within minutes.
What is the difference between Milli-Q water and distilled water?
Milli-Q is a brand name for ultrapure Type I water, produced on demand by RO, ion exchange, UV and filtration. Distilled water has more ions and organics and is usually stored, which lets it pick up CO2 and contamination.
Request a quote for the equipment your lab water feeds.